You’ll finally get that insurance policy without the rejection letter. No more calls from your agent saying they can’t cover you until the wiring’s gone.
Your outlets work the way they should. Three-prong plugs fit without adapters. You can run your AC, charge your car, and use modern appliances without tripping breakers or wondering if something’s about to overheat.
If you’re selling, buyers won’t walk away during inspection. If you’re refinancing, lenders won’t flag your electrical system. And if you’re staying put, you sleep better knowing the wiring behind your walls isn’t a fire waiting to happen. Nearly a quarter of Attleboro homes were built before 1940, which means old wiring removal in Attleboro, MA is more common than you’d think. You’re not alone in dealing with this.
We’ve handled electrical systems across Rhode Island and Massachusetts for more than three decades. We’re licensed Master Electricians, not handymen trying to figure it out as we go.
We’ve completed over 1,500 commercial projects and countless residential upgrades. Knob and tube removal isn’t new to us. We know what it takes to open walls, run new wire, upgrade panels, and close everything back up without turning your house into a construction zone.
Attleboro homeowners call us because we show up, do the work right, and don’t disappear halfway through. We’re not the cheapest option, and we won’t pretend to be. But if you want your electrical system upgrade for old homes in Attleboro, MA done correctly the first time, that’s what we do.
We start with a walkthrough. You show us the house, we look at your panel, check the attic and basement, and map out where the knob and tube wiring runs. Then we give you a clear estimate with no surprises buried in fine print.
Once you’re ready to move forward, we pull permits and schedule the work. We open access points in walls or ceilings where needed, pull out the old wiring, and run new Romex cable that meets current code. If your panel needs an upgrade from 60 amps to 100 or 200, we handle that too.
After the new wiring’s in, we connect everything, test the system, and call for inspection. The inspector signs off, we patch and clean up, and you’re done. The whole process usually takes a few days depending on the size of your home. You’ll have updated wiring, a system that can handle modern electrical loads, and documentation you can hand to your insurance company or realtor.
Ready to get started?
You get full removal of knob and tube wiring from active circuits. We don’t leave sections behind or tell you “it’s fine if it’s not being used.” If it’s there, we take it out.
We install new wiring that’s grounded and code-compliant. That means three-wire systems with hot, neutral, and ground. Your outlets will be grounded, your circuits will be protected, and your home will meet National Electrical Code standards.
Panel upgrades are part of the conversation. Most homes in Attleboro with knob and tube are running on 60-amp service, which isn’t enough for today’s demands. We’ll upgrade you to 100, 150, or 200 amps depending on what your home needs. And because Massachusetts offers Mass Save rebates up to $7,000 for this kind of work, we’ll point you toward those programs so you’re not paying full price out of pocket. Attleboro’s housing stock includes thousands of older homes, and many qualify for financial assistance when upgrading electrical systems.
Most full-house replacements in Attleboro run between $12,000 and $35,000. The range depends on your home’s size, how much wiring needs replacing, and whether you need a panel upgrade.
A small cape with minimal wiring might land on the lower end. A larger colonial with wiring running through multiple floors and a finished basement will cost more. If we need to open walls or ceilings to access the wiring, that adds time and labor.
The good news is that Massachusetts offers Mass Save rebates up to $7,000 for knob and tube removal, especially if it’s preventing you from insulating your home properly. That can cut your out-of-pocket cost significantly. We’ll walk you through what applies to your situation during the estimate.
Yes. Most insurance carriers in Massachusetts either refuse to write new policies for homes with active knob and tube wiring or require you to remove it within 30 to 60 days of closing.
Some companies will cover you but charge higher premiums. Others won’t touch it at all. If you’re buying a home and the inspection reveals knob and tube, expect your insurance agent to ask for proof of removal before they’ll issue a policy.
If you already own the home and your carrier finds out during a renewal or claim, they may non-renew your policy or deny coverage for electrical fires. It’s not a scare tactic. It’s standard practice because knob and tube wiring wasn’t designed for modern electrical loads, and insurers see it as a liability.
You can, but it limits what you can do with your home. You won’t be able to insulate properly because knob and tube wiring overheats when surrounded by insulation. That means higher energy bills and uncomfortable rooms.
You also can’t run modern appliances safely. Knob and tube systems weren’t built for air conditioners, electric car chargers, or the electrical load of a typical household today. You’ll trip breakers, blow fuses, or worse, overheat wiring inside your walls.
If you ever want to sell, buyers will either walk away or negotiate the cost of replacement off your asking price. Lenders often won’t approve mortgages for homes with knob and tube unless it’s removed. So even if it’s “working fine” right now, it becomes a problem the moment you need insurance, want to sell, or try to add insulation.
Most homes take three to seven days depending on size and complexity. A small ranch with straightforward access might be done in three days. A two-story colonial with finished walls and limited attic access could take a full week.
We’re not tearing your house apart. We open strategic access points, run new wire, and close things back up. If you have an unfinished basement or accessible attic, the work goes faster. If everything’s finished and we need to open walls, it takes longer.
You can stay in the house during the work. We’ll need to shut off power in sections while we’re working, but we coordinate with you so it’s not a major disruption. Once the wiring’s in and the inspection’s passed, you’re done. We don’t drag it out or leave jobs half-finished.
Usually, yes. Most homes with knob and tube wiring in Attleboro, MA are running on 60-amp service, which isn’t enough for a modern household. You need at least 100 amps, and many homes benefit from 200-amp service.
A 60-amp panel can’t handle central air, electric heat, a dryer, and a refrigerator running at the same time without tripping. If you’re replacing the wiring anyway, upgrading the panel makes sense. It future-proofs your home and ensures you’re not maxing out your electrical capacity every time you turn something on.
The panel upgrade adds to the cost, but it’s not optional if you want your electrical system to work properly. We’ll assess your current setup during the estimate and tell you exactly what you need. No upselling, just honest recommendations based on your home’s actual electrical load.
Yes. Massachusetts offers Mass Save rebates up to $7,000 for knob and tube wiring removal, especially if the old wiring is preventing you from insulating your home. The program is designed to improve energy efficiency, and knob and tube wiring blocks that because you can’t safely insulate around it.
You’ll need to work with a qualified contractor and follow the program’s requirements, but the rebate can cover a significant portion of the replacement cost. Some homeowners also qualify for additional incentives depending on income and home energy audits.
We can point you toward the right resources and help you understand what’s available. The application process isn’t complicated, but it does require documentation and proof that the work was done to code. We handle jobs like this regularly, so we know what the program looks for.
Local Resources
Useful Links
